A ribbon ethanol fire is not simply a linear burner dropped into a wall. In a custom fireplace project, it is a visual centrepiece, a fuel-handling system, a control interface, and a safety device that must be resolved before joinery, stonework, or metalwork is finalised. Designers who treat the ribbon fire as a late-stage appliance often create avoidable problems: awkward service access, unclear control locations, mismatched flame intent, or a fireplace opening that cannot accommodate the chosen burner. The better approach is to write a precise specification early, then use it to compare technical responses from Bioethanol Fireplace Manufacturers.

Define the Ribbon Geometry and Visual Intent

Start with the linear opening: the visible flame length, the depth of the firebox, the height of the flame bed, and the relationship between the burner and the surrounding material. A ribbon fire is viewed along its length, so the designer should specify whether the flame should read as a continuous line, a segmented sequence, or a controlled band. The manufacturer’s range may include ribbon ethanol fires from 40cm to 300cm, but the design brief should not stop at a nominal size. It should show the finished opening dimensions, the intended reveal, and the sightlines from the main seating positions.

The visual brief should also state how the ribbon meets the ends of the fireplace. Will it terminate in a clean metal edge, a recessed channel, or a custom frame? Art Fireplace notes that custom frames, fireplace glass, and panel colours can be part of the scope, so these should be drawn and specified rather than left to site interpretation. If the ribbon is part of a larger composition in stone, plaster, or timber, the designer must confirm which elements are structural, which are decorative, and which must be removable for service.

Lock Down the Control, Fuel, and Safety Brief

The control strategy is just as important as the flame line. The designer should specify whether the fire is manual, automatic, or flame-control automatic, and where the user interacts with it. A remote control and a button ON/OFF are useful only if the receiver, battery or AC charger, and control panel can be reached without dismantling the fireplace. If the project includes an automatic burner, the specification should ask for clear information on ignition and extinction, automatic filling, and the separation of the bioethanol tank from the burning hearth. These details affect the planning of cupboards, access panels, and adjacent joinery. A remote control is not a substitute for a clear control philosophy. The designer should document who operates the fire, whether the controls are concealed or visible, and how a guest or homeowner will understand the shut-off procedure. Even a simple button sequence needs to be considered in the finished interior.

Safety provisions belong in the design brief, not in a footnote. Ask the manufacturer to explain how the burner monitors its environment and what happens when conditions change. The linked manufacturer describes a CO2 safety infrared detector that stops the fire at unauthorised levels, electronic heat detectors that trigger automatic extinction, a cut-off if the burner is moved by external force, and a child lock. It also mentions an automatic electric pump for filling the combustion tray. Designers do not need to write these as engineering instructions, but they do need to know where sensors sit, how they are tested, and whether any part of the system is visible or requires ventilation or access.

  • State the flame length and finished opening dimensions.
  • State manual, automatic, or flame-control operation.
  • Locate the control panel, remote receiver, and power or battery access.
  • Confirm fuel filling method and access to the tank and burner.
  • Confirm sensor positions, shutdown logic, and child-lock requirements.

Coordinate Materials, Finish, and Installation Details

Ribbon fires are often specified in stainless steel, but the material schedule should be explicit. Art Fireplace refers to stainless steel and MDF in some automatic burner information and to stainless steel 304 with 3mm thickness for a manual burner; the designer should match the specification to the actual model under consideration rather than assuming a generic finish. The fireplace panel colour, glass, frame, and hearth should be co-ordinated with the interior palette, and any visible fasteners or seams should be agreed in advance. For a seamless look, the manufacturer and fabricator need to exchange drawings, not just finish samples.

Installation planning should identify the sequence of work. The burner, tank, control board, and any battery or charger location may need to be installed before the surround is closed. The designer should reserve service access and ask how the unit is lifted, levelled, and connected. Art Fireplace notes that its intelligent ethanol fireplaces use ST semiconductor chips, multiple precise electronic sensors, and an ISO-9001 management system; these are useful prompts for questions about control reliability and production quality, but they should be verified against the selected model. The point is not to collect brand claims, but to make sure the specification can be built, maintained, and serviced. The designer should also check that the manufacturer’s installation instructions, model details, and service information are available in a form the site team can use.

Vet the Manufacturer and the Custom Scope

Before the ribbon fire is approved, the designer should confirm that the manufacturer can deliver the custom scope, not only a catalogue burner. Art Fireplace describes itself as a supplier and manufacturer of custom ethanol fireplaces, intelligent burners, and related products, with custom frames, glass, and panel colours available. The company also states that it has 10+ designers, 8 production lines, 80 workers, and a production capacity of 1,000 units per month. For a design team, those facts are most useful as discussion points: who reviews the shop drawings, who signs off the flame length and control layout, and who provides installation instructions and after-sales support?

Ask for the documentation that the project actually requires, such as CE/FCC/IC certification where applicable, and check that the proposed model matches the specification. Ribbon fires need to be considered as part of the whole fireplace assembly, so the final design brief should tie together dimensions, flame control, fuel access, safety logic, materials, and service strategy. The designer’s schedule should record the approved model, finish, control type, and access requirements so that the contractor is not working from verbal assumptions. When these points are settled early, the ribbon ethanol fire becomes an integrated design element rather than a late compromise, and the custom fireplace is more likely to look intentional, operate predictably, and remain serviceable after handover.